Qual o FAN normal?

Qual o FAN normal?

What is the difference between LL and QL fans

The QL and LL are different in that the QL have more LED's on the back side of the Fan's this allows for more illumination inside the case. The RPM range on the LL is 600 – 1500 RPM, The RPM range on the QL is 525 – 1500 ±10% RPM. so fairly similar there.

Is QL 120 better than LL120

so actually on paper the ll 120 is a better in that they make less noise and have better air flow however for lighting purposes. and a much more premium. design the QL 120. certainly stand out a lot more they look better from both angles.

Should I set fans to PWM or DC

If you have a 3-pin fan connector, pick DC mode. On the other hand, if you have a 4-pin fan connector, select PWM mode. If your motherboard fan header only has 3 pins, pick DC regardless of whether you have a 4-pin PWM or 3-pin DC fan.

What is the difference between PWM and normal fans

Technically speaking, PWM fans are strictly superior to DC fans in nearly every metric—performance, durability, and power efficiency—so it might surprise you to hear that if fans were included with your case, they're most likely DC fans, with the exception of the CPU fan.

Can I use QL fans on radiator

the QL series would be better for radiators\heatsinks due to it's higher pressure pushing through fins. but the ML series claims it has a bit more airflow so in a more open intake\exhaust position, it would potentially get better results than the QL.

What is the max rpm for QL fans

– Keep your system cool with powerful fan speeds up to 1,500 RPM, pushing up to 41.8 CFM of air.

Are QL120 loud

That being said, there is also a bit more noise associated with the QL120 RGB fans when at full speed, topping out at 37 dB. Many will opt for PWM control anyway, so this may not be a concern to many, but all the same, it needs to be mentioned.

What is the difference between LL120 and QL120 reddit

What are the differences Both are nice, and similar as far as cooling goes. The LL (Light Loop) have both inner ring and outer ring lighting. The QL (Quad Loop) have inner ring and outer ring lighting, but on both front and back.

Are PWM fans always full speed

With high- frequency PWM, the fan can be run at speeds as low as 10% of full speed, while the same fan may only run at a minimum of 50% of full speed using linear control. It is more energy efficient, because the fan is always either fully on or fully off.

Why are DC fans more efficient

In DC motors the direct power source (AC) connects to a transformer which converts the power to DC. This decreases the amount of power used by only using a direct current instead of an alternating one.

Is PWM good or bad

PWM is considered to be an easy (or cost-effective) way to control the brightness, but it has serious drawbacks, such as flicker that may cause eye strain and headaches.

Which is better QL or ML fans on AIO

the QL series would be better for radiators\heatsinks due to it's higher pressure pushing through fins. but the ML series claims it has a bit more airflow so in a more open intake\exhaust position, it would potentially get better results than the QL. then you can figure in that the QL produces more noise.

Can you use regular fans on a radiator

Radiators can basically use any fan. Any fan will move some air and the water cooling loop will work.

What is the max fan speed of ql120

1,500 RPM

– Keep your system cool with powerful fan speeds up to 1,500 RPM, pushing up to 41.8 CFM of air. – A low-noise, semi-transparent 120mm fan blade is engineered for quiet operation while also allowing your RGB lighting to shine through.

Is it OK to max fan speed

Is it OK to run fans at max speed Yes, It will not damage anything to run the fan at full speed, but you will have to put up with more noise. The only thing that will damage the computer is running the fan too slow. That will cause the CPU to overheat and fail prematurely.

How many decibels is Corsair QL120

The Corsair iCUE QL120 RGB spins at 1500RPM and is rated at a maximum 41.8 CFM, 26 dB, and 1.55 mmH2O.

Are PC fans supposed to be loud

Your computer fan gets loud because of high internal temps caused by 100% disk usage, high RAM usage, dust and dirt in the vents, or lack of airflow. It's normal for your fan to get loud sometimes, but if it makes a loud rattle for a while, you should investigate.

What is the noise level of QL120

Corsair iCUE QL120 RGB

Cooler Type Case Fan
Fan Thickness 1.0" / 25.00 mm
Fan Speed 525 to 1500 rpm
Static Pressure 1.55 mm H2O
Noise Level 26 dBA

Are Corsair LL120 fans good for cooling

ll120s are not designed as such and will not give you as good performance through the radiator, although they are still good airflow fans when used as intake or exhaust fans.

How do I force my PWM fan full speed

Hi, if you simply remove the 4th, PWM control wire from the fan plug the fan will run at full speed. It's usually green or blue coloured, with the aid of a pin or thin blade you can press the tab in the back of the plug that holds the wire in and just pull it out.

Should I run all my fans at full speed

Yes, it is OK to use 100% fan speed when necessary. There is no harm in using 100% fan speed, as long as you do not do it all the time. You might think that it will damage the computer or cause too much noise. The truth is that you need to use 100% fan speed to keep your computer cool from overheating.

What is the disadvantage of DC fan

Disadvantages of DC Ceiling Fans

DC ceiling fans tend to be more expensive to purchase, although, this cost has come down significantly with improvements to technology and manufacturing. Even being more energy efficient, it could take a long time for you to see the pay-off of buying a DC fan.

Is AC or DC better

AC is better used for long-distance power transmissions and high-power applications in homes, factories, and other establishments. In contrast, DC is better used for storing power in batteries and low-power applications in electronics.

What is normal PWM frequency

PWM frequencies not less than 50 kHz for brushless dc motors are recommended. PWM frequencies of 80 kHz or more would be even more appropriate for motors with a very small electrical time constant.

What happens if PWM frequency is too high

As the PWM frequency is increased beyond a threshold value, the PWM on and off time becomes less than the time required for the RL circuit to operate and the current to reach its steady state. Hence, the current oscillates between two non-steady state values, which gives rise to current ripple.